How to setup Enoocean Switch to Nod On Relay?

How to setup Enoocean Switch to Nod On Relay?

This guide covers pairing your Retrotouch EnOcean Smart Kinetic Switch with the NodOn EnOcean In-Wall/Lighting Relay Modules (e.g., SIN-2-1-xx or SIN-2-2-xx series).

Because both devices native-link across the standard EnOcean Rocker Switch Profile , No smart hubs, internet bridges, or apps are required.

The System Mechanics (How It Controls the Relay)

When paired as an EnOcean Rocker Switch, the relay tracks the top and bottom positions
of the physical rocker:

  • The Rocker Side You Press During Pairing: Becomes the designated "ON" button (and brightens, if using a dimming profile).

  • The Opposite Side of that Rocker: Automatically assigns itself as the "OFF" button
    (and dims).

Step-by-Step Pairing Guide

Before beginning, ensure the NodOn relay is wired safely behind your light fixture or wall box and that the main electrical breaker is turned
ON
.

1. Put the NodOn Relay into Pairing Mode:

Forces the relay to listen.

Locate the small physical programming button on the body of the NodOn relay module.

Give this button a crisp Triple Press (3 consecutive presses within 2 seconds).

  • Visual Confirmation: The diagnostic LED on the NodOn module will start glowing solid Red.

  • Load Confirmation: The connected light fixture will begin to physically toggle ON and OFF once every second, indicating the receiver is open for pairing transmissions.

2. Send the Pairing Signal from the Switch:

Fires the EnOcean profile payload.

Walk over to your unmounted or wall-mounted Retrotouch Kinetic switch.

Choose the specific rocker button you want to use to turn the light ON. Press that button down firmly and completely once. You must hear the loud, crisp mechanical clack of the internal kinetic generator firing.

3. Confirm the Link:

Locking the security pairing keys.

Look back at the NodOn relay module to verify it successfully intercepted the 868 MHz payload:

  • Success Signal: The relay's diagnostic LED will flash Green twice. The connected light fixture will stop cycling every second and drop into a steady state.

  • Automatic Exit: The relay will immediately close its pairing window and revert back into its normal, active Operating Mode.

Mapping Multi-Gang Configurations (1-Gang vs. 2-Gang)

  • If using a 1-Gang Plate (Single Large Rocker): Performing the guide above creates a traditional single zone setup.
    Pressing the top of the rocker turns the relay ON; pressing the bottom turns it OFF.

  • If using a 2-Gang Plate (Split Dual Rockers): You can control two separate
    single-channel NodOn modules (or control Channel 1 and Channel 2 on a dual-channel NodOn light relay).
    To do this:

    1. Put Relay A
      into pairing mode
      $\rightarrow$ Press the Left Rocker
      on the Retrotouch switch.

    2. Put Relay B
      into pairing mode
      $\rightarrow$ Press the Right Rocker
      on the Retrotouch switch.

Troubleshooting & Reset Routines

  • The Issue:
    The internal non-volatile memory cache inside the NodOn module is completely full.
    NodOn relays can hold a maximum memory allocation of 22 distinct wireless controllers
    simultaneously.

  • The Fix:
    You must perform a factory hardware reset on the relay to clear the old controller tokens.

Factory Resetting the NodOn Relay Module

If you need to completely wipe the relay's pairing memory to start fresh:

  1. Press and hold down the local button on the NodOn module for more than 5 seconds until its LED turns
    Orange
    .

  2. Release the button.
    The LED will remain steady Orange, entering a 30-second confirmation window.

  3. Press the local button once briefly
    to validate the reset sequence.

  4. The LED will blink Red and Green alternatively
    to confirm that the memory is entirely cleared.